I Didn’t Realize You Were The Person Who Did The Fanfiction Tag Drinks.

I think the dream I had regarding mouthwashing last night will haunt me for awhile 💐👁

So this is something that I'm working on. 12h in and it's still not done. Trying not to rush. Really love it so far.

PART TWO: THE END

Art by Matteo Moni

Listen.

EVERYBODY knows (or should) that you DO. NOT. STOP. in Vidor, Texas. 

It’s best to just run out of gas elsewhere. Whatever you do, black folks, DO NOT STOP IN VIDOR, TEXAS. 

There’s a good chance you’ll get lynched or just come up missing - and I’m not joking.

also do NOT stop in Harrison, Arkansas!!!! (relatively close to OK and MI) a nazi town with a BIG KKK organization.

Reblog To Save Life

TRICK OR TREAT! Mind giving me some sweets?

please accept this 30 min halloween comic as a treat lol

𝐓𝐡𝐞 𝐇𝐞𝐫𝐚𝐥𝐝

It truly took me the second coming of Jesus to get back to work—

A portrait of Viktor to distract myself from crying over Jayvik (not effective. I’m in fact planning to do a matching painting of Jayce. This is my life now)

Hello! I was wondering what company you use for your sticker sheets? I bough one from your Ko-Fi shop and really like the quality, and the pricing you were able to sell at is waaaaaay more reasonable compared to any of the companies I've seen and used myself. Is it a POD company, or a mass purchase of them to sell on your own?

Thank you for your time if you're able to respond!

I'm really glad you like the quality, because I actually make them by hand at home! (Please forgive the lighting, my bedroom is my office lmao.)

I don't use a company (and Idk what a POD company is sorry!) but making them at home gives a lot more freedom of stock, just be wary it can be very time consuming depending on how many you need to make.

I've had other people ask before, so here's a rundown of how I make my stickers at home: At most you'll need:

Printer

Sticker paper (this is the type that I use)

Laminator and lamination paper (the lamination paper that I use.) You can also use adhesive non-heat lamination paper if you don't have a laminator, gives you the same result, just be careful of bubbles. You will get double your worth out of a pack because we are splitting the pouches to cover two sticker sheets.

Your choice of a sticker cutting machine or just using scissors.

First, I use Cricut's software to print out the sticker sheet with the guidelines around the corners so the machine can read it. If you do NOT have a Cricut machine, open up your art program, make a canvas of 2550x3300 and fill it up with your sticker design with some cutting space between them. This the 8.5x11 size for the sticker page.

I usually have bleed selected so the cut comes out cleaner. Tip for non-Cricut users below: Increase the border around your sticker design to fake the 'bleed' effect for a cleaner cut.

These are the print settings I use for my printer. I use the 'use system dialogue' to make sure I can adjust the settings otherwise it prints out low quality by default. Make sure if you're using the above paper that you have 'matte' selected, and 'best quality' selected, these aren't usually selected by default.

So you have your sticker sheet printed! Next is the lamination part. I use a hot laminator that was gifted to me, but there is no-heat types of lamination you can peel and stick on yourself if that's not an option.

(This is for protection and makes the colors pop, but if you prefer your stickers matte, you can skip to the cutting process.)

Important for Cricut users or those planning to get a Cricut: You're going to cut the lamination page to cover the stickers while also not covering the guidelines in the corners. First, take your lamination page and lay it over the sheet, take marker/pen and mark were the edges of your stickers are, and cut off the excess:

(I save the scrap to use for smaller stickers or bonuses later on)

After you've cut out your lamination rectangle, separate the two layers and lay one down on your sticker sheet over your stickers with matte side down, shiny side up. (Save the other sheet for another sticker page)

The gloss of the lamination will prevent the machine from reading the guidelines, so be careful not to lay it over them. It also helps to cut the corners afterwards to prevent accidentally interfering with the guidelines.

Now put that bad boy in the laminator! (Or self seal if you are using non-heat adhesive lamination)

Congrats! You now have a laminated page full of stickers.

For non-cricut/folks cutting them out by hand: this is the part where you start going ham on the page with scisscors. Have fun~

Cutting machine: I put the page on a cutting mat and keep it aligned in the corner, and feed it into the machine. For laminated pages I go between 'cardstock' and 'poster board' so that it cuts all the way through without any issues, but for non-laminated pages or thinner pages, I stick for 'vinyl' and 'light card stock'. Kinda test around.

Now I smash that go button:

You have a sticker now!

The pros of making stickers at home is that you save some cost, and you have more control of your stock and how soon you can make new designs. (I can't really afford to factory produce my stickers anyway)

However, this can be a very time consuming, tedious process especially if you have to make a lot of them. There is also a LOT chance for some errors (misprints, miscuts, lamination bubbles, ect) that will leave you with B-grade or otherwise not-so-perfect or damaged stickers. (Little note, if you have page mess up in printing and can't be fed into the cricut machine, you can still laminate it and cut it out by hand too.)

I have to do a lot of sticker cutting by hand, so if you don't have a cricut don't stress too much about it. I have an entire drawer filled to the top of miscuts/misprints. I keep them because I don't want to be wasteful, so maybe one day they'll find another home. Sucks for my hand though.

But yeah! This is how I make my stickers at home! Hope this is helpful to anyone curious

A Closer Look: Vertebrates

The Vertebrata clade can be split into 3 main groups: neomammalia (new mammals) and brachipteryxus (wing-armed) - the tetrapods; as well as polypodus (many-footed) - their distant six-legged cousins.

Examples of chordates: Dolichocerca leo, the ocelot (neomammalia); Lepidoscelus igneamantis, the strider (brachipteryxus); and Neopolypodus flavitta, the bee (polypodus).

Neomammalia and brachipteryxus are both notable survivors of Primordial Death, the mass-extinction event that eliminated the majority of life in the realms prior to the players’ entry. Neomammalia in particular had many surviving members, and has since continued to diversify.

A chicken (Myriapinna polynativas) and a sheep (Lanatumorphus myriachroma), both survivors of Primordial Death.

Polypodus is considered a lazarus taxon - a group of organisms that was considered extinct, but reappeared later. Bees were discovered first - long after the players’ emergence - and defined the previously unknown polypodus taxon. It was believed they were the only extant polypod, until ancient sniffer eggs were discovered - and miraculously hatched.

A snifflet (juvenile Anchipolypodus aeternovis).

Return to full tree.

Neomammalia.

Brachipteryxus.

Polypodus.

this week's sneepsnorp club update just went out! :D project birdbrain update 6 is up to check out in my art journal, and there's an update on delayed sticker club rewards!